I recently upgraded from a Garmin Forerunner 305 to a Garmin Edge 500 as my number-producing gadget for cycling stats. While the Forerunner is still what I’ll use whenever I go on runs, I’ve used the Edge on several rides now and have found it to be a huge improvement over the Forerunner.
Since it’s still relatively new (i.e., it was announced ages ago but it recently started actually shipping finally) and I couldn’t find a ton of data on it yet from other folks who have gotten their hands on it, I’m going to write up what I’ve noticed so far hoping it helps someone out who’s deciding on whether to pick this one up or not.
The good:
- The screen is large and very easy to read. You can have up to 8 different data points on any of the three “pages” available to you.
- USB port is on the device itself. No need for a cradle like the Forerunner did.
- Elevation detection is way better than the Forerunner. For example, it wasn’t uncommon for me to ascend 300-400 ft while on a *trainer* in my garage when using my Forerunner. The Edge 500 reports a nice comforting zero every time so far.
- The calories burned reported by the device are a lot more realistic than the Forerunner. Since it uses your heart rate (and maybe some other data) to calculate the calories burned, it’s clearly going to report much more accurate numbers.
- There’s a “Start Notice” feature that does a decent job of alerting you that you’ve started moving and you haven’t pressed “Start” yet. I know that’s happened to me many times in the past and this will surely help me out.
- The way it attaches to your bike’s stem seems more reliable than the mount they offer to hook up a Forerunner to a bike with. I’ve seen the Forerunner fall off those mounts but the twist-mechanism used for the Edge seems pretty secure.
- It’s got a thermometer that now uploads the temperature for each ride to Garmin Connect. I don’t think it’s accurate–it’s always a bit high–but it might be helpful to just compare the deltas from ride to ride.
- It also seems to have more stats like “Grade %” that I don’t remember seeing on the Forerunner.
The bad (all pretty minor–so far):
- The USB port is protected by a small rubber cover that isn’t all that easy to seal shut. Not a huge problem but still a little tedious.
- The Start/Stop and Lap buttons are a little harder to press while riding as they’re on the side of the device. I thought the Forerunner’s buttons were better positioned.
- The calories burned are more accurate than the Forerunner. While this is obviously good there was something extra encouraging about being lied to by the Forerunner’s ridiculously high numbers. :)
Update (12/19/2009): Looks like there’s an updated ROM for the Edge 500 that fixes a few things I hadn’t run into until today. You can get the update from here.


Comments
Hi, Gus:
Thanks for the nice review! I was just touted on the 500 by a bike store salesman and was looking for real life user info. Sounds pretty good to me!
One question: I am new to wanting to use the same device for outdoor riding, mostly mtb touring, and on my trainer indoors…how do you accomplish that with the Garmins? And are there any “tricks of the trade” you can share in switching back and forth like that?
Happy Happy!
Patrick
Hey Patrick, glad it was helpful. Regarding your question, it came with two mounts so I put those on my two bikes (a road bike and a mountain bike). I currently have my road bike on the trainer. Switching between those two bikes now is super simple–just twist off one and twist it on to the other one.
If you have a third bike you want to mount it on it looks like they sell the mounts separately for $10 on Amazon.
I haven’t actually been riding my mountain bike though so I don’t have actual experience with this but it looks like the Garmin supports at least three different bikes. So I guess the other thing you’d want to do is pick the corresponding bike whenever you switch bikes before a ride. Looks pretty easy to do though.
Hope that helps…
Nice, but what functions can use with just the 500 itself on the trainer, or are you swapping a chainstay sensor as well?
Thanks
Patrick
I don’t get cadence on my mountain bike but I could if I end up using it enough to want it. I’d have to buy another sensor though. Moving the sensor from one bike to another doesn’t look like a feasible plan. Unlike the actual 500, it actually attaches via a zip tie.
Thanks for all the info, Gus, much appreciated.
Patrick
Post a comment here